CXRacing LS1 Engine Mount + T56 Transmission Mount + Subframe + Rear End Differential Bracket + Headers For 1989-1997 1st Gen NA Mazda Miata MX-5 With LS1 Swap

-Heavy Duty Construction Using 7 Gauge (0.18") Thickness Stainless Steel Panels and Tubes.
-Retains Factory Steering Geometry, Bolt On Factory Steering Rack and Pinion.
-Retains Factory Suspension System.
-Comes with Engine Mounts for LS1 Engine
-Comes with T56 Transmission Mount
-Comes with Rear End Differential Bracket for Stock Diff
-Comes with Swaybar Spacer, 4.5" Height
-Stainless Steel Headers with 3" / Oval Exhaust Pipes

Note: Some Brackets Need to be Welded on the Chassis for Stronger Support, See Pictures

This Product was developed based on US model Left-Hand-Drive chassis. For Right-Hand-Drive, due to potential conflict with steering shaft, fitment most likely will be an issue and we don’t guarantee fitment. Modification is needed and we won’t accept return due to Right-Hand-Drive fitment issues.

APPLICATION(S)
Chassis: 1989-1997 1st Gen NA Mazda Miata MX-5
Motor: LS1
Transmission: T56

What's in the box:
This is for the Parts Listed Below, All Other Parts Shown are NOT INCLUDED.

Products:
Subframe, with Swaybar Spacer x1
Set of Engine Mount x1
Set of Transmission Mount x1
Set of Differential Bracket x1
Header Downpipe Kit x1


Write a review

Please login or register to review

LS1 Engine T56 Trans Mounts Subframe Differential Bracket Headers For 89-97 Miata MX-5 LSx

  • Brand: CXRacing
  • Product Code: ESK-TM-HD-LS-SUBFRAME-MIATA9098
  • Availability: In Stock
  • $3,033.01


Tags: CXRacing LS1 Engine Mount + T56 Transmission Mount + Subframe + Rear End Differential Bracket + Headers For 1989-1997 1st Gen NA Mazda Miata MX-5 With LS1 Swap -Heavy Duty Construction Using 7 Gauge (0.18") Thickness Stainless Steel Panels and Tubes. -Retains Factory Steering Geometry, Bolt On Factory Steering Rack and Pinion. -Retains Factory Suspension System. -Comes with Engine Mounts for LS1 Engine -Comes with T56 Transmission Mount -Comes with Rear End Differential Bracket for Stock Diff -Comes with Swaybar Spacer, 4.5" Height -Stainless Steel Headers with 3" / Oval Exhaust Pipes Note: Some Brackets Need to be Welded on the Chassis for Stronger Support, See Pictures This Product was developed based on US model Left-Hand-Drive chassis. For Right-Hand-Drive, due to potential conflict with steering shaft, fitment most likely will be an issue and we don’t guarantee fitment. Modification is needed and we won’t accept return due to Right-Hand-Drive fitment issues. APPLICATION(S) Chassis: 1989-1997 1st Gen NA Mazda Miata MX-5 Motor: LS1 Transmission: T56 What's in the box: This is for the Parts Listed Below, All Other Parts Shown are NOT INCLUDED. Products: Subframe, with Swaybar Spacer x1 Set of Engine Mount x1 Set of Transmission Mount x1 Set of Differential Bracket x1 Header Downpipe Kit x1



Emissions Control Warning:

It is illegal to sell, install, or offer for sale any aftermarket part that alters or modifies the original design or performance of the motor vehicle pollution control system. Product(s) listed here is(are) solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for use on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).

All Products by CX-GARAGE are solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for used on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).
Proposition 65 Warning:

These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.