• Your shopping cart is empty!

CXRacing Chromoly Cylinder Head Stud Kit + Crank Bolt / Harmonic Balancer Bolt for 2005+ GM/Chevy Gen IV LSx 6.0/6.2L Engine

Note: This Stud Kit ONLT Fits Gen IV LSx 6.0L and 6.2L Engines. Does NOT Fit Others!

Features:

- 220,000 PSI Strength

- 12 Point Nuts, with Washers

- Black Oxide Finish

- Comes with:

M11 x 130mm Stud x 20 pcs
M8 x 64mm Stud x 10 pcs
Crank Bolt and Washer x 1 pcs

These Cylinder Head Studs Are Made With High Quality Chromoly Steel, Hold Extreme Strength for High Power Engine Builts, Such As Boosted Applications.

Recommended Torque Spec:

1. First Pass All M11 Bolts in Sequence: 22 lb/ft

2. Second Pass All M11 Bolts in Sequence: 90 degrees, 50 lb/ft

3. Final Pass All M11 Bolts in Sequence (Excluding the Bolts at the Front and Rear of Each Cylinder): 90 degrees, 75 lb/ft

4. Final Pass M11 Bolts at the Front and Rear of Each Cylinder Head in Sequence: 70 degrees, 75 lb/ft

5. M8 Inner Bolts in Sequence: 22 lb/ft

What's in the box?:
 This Item is for the Stud Bolt Kit and Crank Bolt / Harmonic Balancer Bolt ONLY, All Other Parts Shown are NOT INCLUDED.

Product(s):
- 20x M11 Studs
- 10x M8 Studs
- 30x Nuts and Washers
- 1x Bolt + Washer


Installed Photos:

























Write a review

Please login or register to review

Head Stud Bolt Kit + Crank Crankshaft Bolt for GM Chevy GEN IV LS9 LQ9 6.0L 6.2L Engine

  • Brand: CXRacing
  • Product Code: BOLT-KIT-LQ9-CRANK
  • Availability: In Stock

  • $77.27


0 reviews / Write a review

Tags: CXRacing Chromoly Cylinder Head Stud Kit + Crank Bolt / Harmonic Balancer Bolt for 2005+ GM/Chevy Gen IV LSx 6.0/6.2L Engine Fits 2004 and Up Chevy Gen III LS Series, 4.8L / 5.3L / 5.7L Note: This Stud Kit ONLT Fits Gen IV LSx 6.0L and 6.2L Engines. Does NOT Fit Others! Features: - 220, 000 PSI Strength - 12 Point Nuts, with Washers - Black Oxide Finish - Comes with: M11 x 130mm Stud x 20 pcs M8 x 64mm Stud x 10 pcs Crank Bolt and Washer x 1 pcs These Cylinder Head Studs Are Made With High Quality Chromoly Steel, Hold Extreme Strength for High Power Engine Builts, Such As Boosted Applications. Recommended Torque Spec: 1. First Pass All M11 Bolts in Sequence: 22 lb/ft 2. Second Pass All M11 Bolts in Sequence: 90 degrees, 50 lb/ft 3. Final Pass All M11 Bolts in Sequence (Excluding the Bolts at the Front and Rear of Each Cylinder): 90 degrees, 75 lb/ft 4. Final Pass M11 Bolts at the Front and Rear of Each Cylinder Head in Sequence: 70 degrees, 75 lb/ft 5. M8 Inner Bolts in Sequence: 22 lb/ft What's in the box?: This Item is for the Stud Bolt Kit and Crank Bolt / Harmonic Balancer Bolt ONLY, All Other Parts Shown are NOT INCLUDED. Product(s): - 20x M11 Studs - 10x M8 Studs - 30x Nuts and Washers - 1x Bolt + Washer



Emissions Control Warning:

It is illegal to sell, install, or offer for sale any aftermarket part that alters or modifies the original design or performance of the motor vehicle pollution control system. Product(s) listed here is(are) solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for use on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).

All Products by CX-GARAGE are solely for Competition Vehicles(race vehicles) that are for Off-Road, Track Racing ONLY. All parts are for used on a vehicle that will NEVER be used, or licensed, or registered for use upon a street and highway. DO NOT Purchase the part(s) if you are intending to use it(them) on a Street/Highway vehicle(s).
Proposition 65 Warning:

These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.