• Your shopping cart is empty!

CXRacing 11 Gauge Thick Wall Single Top Mount Turbo Manifold + WG Dump Tube For 2003-2012 Mazda RX-8 With RX-7 FD REW 13B Engine Swap

Manifold FitsT4 Turbo, with 3" Vband Exhaust Housing, and 60mm Vband Wastegate

Note:

1. Due to Limited Space and the Difficulty Of RX8/13B Turbo Swap, There Is ONLY Very Small Room Available for Manifold and Turbo. This Manifold ONLY Fits CXRacing's Engine Mount Kit (Which Oil Pan Sits Approximate 3/4 Inch Lower than the Lowest Point Of the Front Cross Support, See Below Picture). If Your Engine Sits Differently with More Than 1/4"" Difference. This Manifold Won't Fit.

2. This Kit Is Developed Based On US Model Left-Hand-Drive. For RHD, We Have Not Tested and Don't Know If There Is Any Fitment Problems (Primary Issue Is Steering Shaft Might Hit Other Parts). We Don't Guarantee Fitment for RHD Chassis.

Application:
Chassis: 2003-2012 Mazda RX8
Engine: RX-7 FD 13B Turbo
Note: This Is A Single Turbo Kit, Does NOT Fit Stock Twin Turbo

Product Info and Spec:

Manifold and Downpipe Kit:
-11 Gauge Thick Wall Manifold
-T4 Flange, 60mm Vband Wastegate Flange

Notes:

-Off Road or Track Use ONLY, NOT for Street Use

-Due to the Complexity of Swapping a Motor to Different Chassis, Please Make Sure that You Understand the Application Stated Here are the Right Parts for Your Project

- Parts Being Sold are the Kit Being Advertised ONLY. Other Parts Shown on Pictures are for Demo Only (of Our Complete Swap Kit). Check Our Other Products.
　 　 　 　 　 Note: With Our Mount Kit, Oil Pan Sits Approximate 3/4 Inch Lower than the Lower Point Of the Front Cross Support Turbo Manifold Installed Pictures: 　 　 　 　 　 　 　 　 　 　 　 　 　

Write a review

Please login or register to review

Thick Wall Manifold for RX8 RX-8 13B Turbo Swap T4 60MM WG Flange

  • Brand: CXRacing
  • Product Code: MF-13B-RX8-WT
  • Availability: In Stock

  • $573.99


0 reviews / Write a review

Tags: CXRacing 11 Gauge Thick Wall Single Top Mount Turbo Manifold + WG Dump Tube For 2003-2012 Mazda RX-8 With RX-7 FD REW 13B Engine Swap Manifold FitsT4 Turbo, with 3" Vband Exhaust Housing, and 60mm Vband Wastegate Note: 1. Due to Limited Space and the Difficulty Of RX8/13B Turbo Swap, There Is ONLY Very Small Room Available for Manifold and Turbo. This Manifold ONLY Fits CXRacing's Engine Mount Kit (Which Oil Pan Sits Approximate 3/4 Inch Lower than the Lowest Point Of the Front Cross Support, See Below Picture). If Your Engine Sits Differently with More Than 1/4"" Difference. This Manifold Won't Fit. 2. This Kit Is Developed Based On US Model Left-Hand-Drive. For RHD, We Have Not Tested and Don't Know If There Is Any Fitment Problems (Primary Issue Is Steering Shaft Might Hit Other Parts). We Don't Guarantee Fitment for RHD Chassis. Application: Chassis: 2003-2012 Mazda RX8 Engine: RX-7 FD 13B Turbo Note: This Is A Single Turbo Kit, Does NOT Fit Stock Twin Turbo Product Info and Spec: Manifold and Downpipe Kit: -11 Gauge Thick Wall Manifold -T4 Flange, 60mm Vband Wastegate Flange



Emission Notes:

All Parts and services offered by CX-GARAGE are for competition vehicles only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this competition use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assumes all associated risk of the purchase.

Federal and several state laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. CX-GARAGE assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer’s modifications and/or use of CX-GARAGE products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
Proposition 65 Warning:

These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.