• Your shopping cart is empty!

CXRacing Turbo Throttle Body Y Pipe Kit For Toyota 2JZ-GTE Engine

For Some 2JZGTE Swaps, Factory Cast Twin Turbo Y Pipe Sits Too High and Hitting the Hood. Our New Y Pipe Resolves This Issue with Lower/Better Clearance, About 3/4" Lower than Factory Y Pipe

1.75" Aluminum Y Pipes Merge Into Single 3" Pipe Also Offers Better Air Flow and Increase Performance.

Pictures Shown Below is For IS300 Swap

Note:
3" Pipe Does NOT End at Exactly Where the Factory Y Pipe Ends, It is Slight Downward. So If You Use This Y Pipe to Match Your Existing Intercooler Piping. It Might Need Minor Modification or Use a Different Angled Hose

Application:
Chassis: Many Chassis
Motor: 2JZ-GTE
Turbo: 2JZ-GTE Stock Twin Turbo

Product Being Sold:
Pipe + Hoses + Clamps

This is CXRacing's Newest Products for the Application Stated Above. All Parts Are Developed from Ground Up in Our R&D Center in USA, Designed and Built for Improved Performance Gains, with Excellent Fitment and Easy Installation.

Notes:
Off Road or Track Use ONLY, NOT for Street Use
Due to the Complexity of Swapping a Motor to Different Chassis, Please Make Sure You Understand the Application Stated Here is the Right Parts for Your Project
　
　
　
　
Highlights：
 -Especially Designed, Made for the Application Stated
 -Fully Tested, Simple Easy Installation
 -Offers Excellent Performance Gains
 -One Of The Best Kits On The Market, With High Quality Products And Affordable Pricing
　
Item Included:
-Aluminum Y Pipe
-Silicon Hoses and Stainless Steel T-Clamps
　
Below Are Installation Pictures:
　
　
　
　
　
　
　

Write a review

Please login or register to review

Turbo Throttle Body Y Pipe Kit For Toyota 2JZ-GTE Engine

  • Brand: CXRacing
  • Product Code: PIP-2JZGTE-TT
  • Availability: In Stock

  • $62.73

Available Options


0 reviews / Write a review

Tags: CXRacing Turbo Throttle Body Y Pipe Kit For Toyota 2JZ-GTE Engine For Some 2JZGTE Swaps, Factory Cast Twin Turbo Y Pipe Sits Too High and Hitting the Hood. Our New Y Pipe Resolves This Issue with Lower/Better Clearance, About 3/4" Lower than Factory Y Pipe 1.75" Aluminum Y Pipes Merge Into Single 3" Pipe Also Offers Better Air Flow and Increase Performance. Pictures Shown Below is For IS300 Swap Note: 3" Pipe Does NOT End at Exactly Where the Factory Y Pipe Ends, It is Slight Downward. So If You Use This Y Pipe to Match Your Existing Intercooler Piping. It Might Need Minor Modification or Use a Different Angled Hose



Emission Notes:

All Parts and services offered by CX-GARAGE are for competition vehicles only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this competition use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assumes all associated risk of the purchase.

Federal and several state laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. CX-GARAGE assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer’s modifications and/or use of CX-GARAGE products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
Proposition 65 Warning:

These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.